ISO 18286 PDF

0 Comments

ISO specifies requirements for tolerances for hot-rolled stainless steel plates (quarto plates) made on a reversing mill with the following. EN & ISO Tolerances for COLD Rolled material (Sheets, plate, coil) up to mm thick. EN & ISO Tolerances for ‘Quarto’ Hot. ISO. Second edition. Hot-rolled stainless steel plates —. Tolerances on dimensions and shape. Tôles en acier inoxydable laminées à chaud.

Author: Arazahn Zuluk
Country: Antigua & Barbuda
Language: English (Spanish)
Genre: Politics
Published (Last): 16 April 2008
Pages: 288
PDF File Size: 16.62 Mb
ePub File Size: 20.97 Mb
ISBN: 667-3-30807-820-7
Downloads: 94435
Price: Free* [*Free Regsitration Required]
Uploader: Doukus

It is quite difficult to compare the flatness tolerances in EN and ISOas the definition of steel iiso is totally different. Provision is made for different width and length tolerances depending on the method of cutting.

Article: Tolerances to ISO for hot rolled stainless steel quarto plates

Tolerances on dimensions and shape Status: Office and Postal Address: Your basket is empty. Therefore, and were given the same flatness tolerance. Shall be agreed at time of enquiry and order. Accept and continue Learn more about the cookies we use and how to change your settings. This is in contrast to EN which was referred to in EN and allowed some areas to be below minimum thickness.

BS EN ISO 18286:2010

The flatness tolerance is dependent on grade. One interpretation of the standard is that no ground area of the plate may fall below the minimum thickness tolerance.

For comparison, EN has an edge camber of 0. This is dependent on the method of cutting the plates.

  ISILON X400 PDF

It isi EN which was not specifically for stainless steel. Take the smart route to manage medical device compliance. There are two levels of tolerance normal Class N and special Class S.

Featured Articles & Publications

This meant that most stainless steels fell into steel type L. Worldwide Standards We can source any standard from anywhere in the world. There are 3 classes of tolerance for width and length for plates with trimmed edges A – C. The class shall be specified at the time of enquiry and order. This may not be realistic. Find Similar Items This product falls into the following categories.

For example, martensitic grades in the quench and tempered condition or high yield strength PH grades are expected to have a better flatness than Even the nitrogen strengthened steels were in this type. For plate with untrimmed 81286 in the enquiry and in the purchase order, the edge camber and out of squareness shall be limited so that it is possible to inscribe a rectangle of the nominal length and width of the ordered plate within the delivered size.

In ENthe inscribed rectangle definition was not restricted to plates with untrimmed edges. An approximate comparison is shown in the following table for a 10mm plate in various grades of steel using the mm measuring length:. You may experience issues viewing this site in Internet Explorer 9, 10 or Learn more about the cookies we use and how to change your settings.

  JADUAL BAYARAN CARUMAN KWSP 2012 PDF

This ixo covers hot rolled stainless steel plates rolled on a reversing mill known as quarto plate. It may also lso taken to iiso plate rolled on a Steckel mill but taken out of the process before coiling has begun.

Tolerances to ISO for hot rolled stainless steel quarto plates General This standard covers hot rolled stainless steel plates rolled on a reversing mill known as quarto plate. Click to learn more.

It removes some anomalies and ambiguities from that standard. It can be argued that neither standard is completely consistent on this subject. For plate with trimmed edges, the edge camber shall not exceed 0.

Steel Type B – Maximum 182886 1. Search all products by. Please download Chrome or 12886 or view our browser tips. We use cookies to make our website easier to use and to better understand your needs. This website is best viewed with browser version of up to Microsoft Internet Explorer 8 or Firefox 3.

If not specified, the manufacturer 182886 supply to either class. You may find similar items within these categories by selecting from the choices below:. There are no tolerances on the maximum difference allowed within a plate. Sheet materials, Stainless steels, Corrosion-resistant steels, Steels, Hot-working, Rolled products, Dimensions, Dimensional tolerances, Form tolerances, Designations, Dimensional measurement.

Thickness The tolerance under nominal thickness is 0.