FISHER DVC6000 PDF
Fisher™ FIELDVUE™ DVCf Digital Valve For more than 20 years, Fisher products have been manufactured with DVC Digital Valve Controller. Fisher r. FIELDVUE™ DVC Digital Valve. Controllers. Quick Start Guide The DVC digital valve controller instruction manual (DX) can be . Note. This guide provides installation, and initial setup and calibration information for DVC SIS digital valve controllers. The following documents are also.
|Published (Last):||10 January 2011|
|PDF File Size:||10.14 Mb|
|ePub File Size:||3.72 Mb|
|Price:||Free* [*Free Regsitration Required]|
If required, attach the spacer to the actuator shaft. Supply pressure must be clean, dry air that DVC Check the control mode using the Field Communicator. Device ID H ! Some of the procedures also contain the sequence of Please be sure to include the model number if you have it.
For additional information, refer to Relay Adjustment in this section. Remove the front cover key Troubleshooting DVC Digital Valve Controllers Troubleshooting Fjsher communication or output difficulties are experienced Note with the instrument, refer to the troubleshooting chart in table Page 75 Detailed Setup Deadband exceeded, Deadband exceeded, and direction new Reference Point changed, new Reference Point established established This amount of change is Point at which added to the Travel Deadband Reference cycle is counted.
DVC Digital Valve Controllers Troubleshooting If communication or output difficulties are experienced Note with the instrument, refer to the troubleshooting chart in table Zero Ctrl Signal 1. Quarter-turn rotary applications meets the requirements of ISA Standard 7.
The analog input signal range that corresponds flsher Firmware is a program that is entered into the the travel range.
Fisher FIELDVUE DVC6000 SIS Digital Valve Controller
Polling Address Measured Var! Refer to figures through for key number locations. Max Supply Press 3. Selecting large, medium, and small adjustments 7. Inst Serial Num 7. Tvl Cutoff High 4. The following message appears: The Performance Tuner is used to optimize digital valve controller tuning.
Be sure the resistance reading remains procedure. Where a key number is referenced, figure In burst mode, the digital valve controller foot.
If using natural gas as the plastic cover when flammable gases pneumatic supply medium, natural gas will be used in or dust are present, do not rub or the pneumatic output connections of the DVC to clean the cover with solvents. A value of 0. Tvl Acum DB 4. Install the external lock washer on the adjustment installations use the long feedback arm [62 mm 2.
Burst Setting mode applies only to the transmission of burst mode Instrument Time Invalid Enable data analog input, travel target, pressure, and travel Calibration in Progress Enable and does not affect the way other data is accessed.
Maintenance and Troubleshooting D Ensure that all caps and covers Tools Required are correctly installed before putting Table lists the tools required for maintaining the this unit back into service.
EMERSON FISHER FIELDVUE DVC INSTRUCTION MANUAL Pdf Download.
Page 42 Contact your Supply and output pressure gauges may be supplied Emerson Process Management sales office for on the digital valve controller.
Remove the screw key 72 that fastens the travel 2. Step response test — Test evaluates hysteresis, dead time, overshoot and stroking time. Connect the second wire of the 3-conductor Table of Contents Add to my manuals Add. Tvl Alert Hi Pt 4.
fisber Tvl Dev Alrt Enab 2. If necessary, reposition the cam to attain alignment. Aux In Airt State 3. Tvl Acum byci count Alert 1. Module Base Maintenance Maintenance and Troubleshooting D Ensure that all caps and covers Tools Required are correctly installed before putting Table lists the tools required for maintaining the this unit back into service.
Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user. Critical NUM Fail 5. No Free Time Fail 3.
Cycl Count DB 4. Install a pipe plug in the vent-away into the surrounding atmosphere. Stroke Valve Detailed Setup!
Replace and tighten the base unit cover. Connect one wire of the 3-conductor shielded cable between terminal 1 on the feedback unit and terminal D Emerson Process Management supplied 1 on the base unit.
Fisher FIELDVUE DVC SIS Digital Valve Controller | Haygor Instrument & Company, Inc.
General When enabled indicates that calibration is in progress. Pneumatic Relay Maintenance and Troubleshooting Table Don’t have an account? Spare parts availability is 7 years of best effort. Attach the travel indicator, to the shaft connector cvc6000 spacer as described in the mounting kit instructions. Analg In Units 2.