ASTM D2310 PDF
Buy ASTM D CLASSIFICATION FOR MACHINE-MADE ‘ FIBERGLASS’ (GLASS-FIBER-REINFORCED THERMOSETTING-RESIN) PIPE from SAI. Find the most up-to-date version of ASTM D at Engineering This classification covers machine-made “fiberglass” (glass-fiber-reinforced thermosetting-resin) pressure pipe. Methods of classification.
|Published (Last):||9 July 2009|
|PDF File Size:||17.22 Mb|
|ePub File Size:||5.87 Mb|
|Price:||Free* [*Free Regsitration Required]|
This standard has been approved for use by agencies of the Department of Defense. Standard categories for the hydrostatic design basis are shown in Table 1. Last previous edition D — Referenced Documents purchase separately The documents listed below are referenced within the subject standard but aetm not provided as part of the standard. There are two designation code generators look up scripts using the ASTM D standard classification.
Precedence for this change has been made in other ASTM standards. The values in parentheses are provided for information only. A hydrostatic design basis as shown in Table 1 shall be determined for each type, grade, and class of product manufactured. This cell-type format, however, is subject to misapplication since unobtainable property combinations can be selected if the user is not familiar with commercially available products.
A The cell-type format provides the means of identification and specification of piping materials. Note 1 — For the purposes of this standard, polymer does not include natural polymers. The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.
Your comments will awtm careful consideration at a meeting of the responsible technical committee, which you may attend. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
B Refer to Practice D to obtain classi?
Or the D Table 1 data can be used to explain how the classification designation code for composite fiberglass piping is derived. Current edition approved June 10, For the second generator, the property must be supplied by the FRP fiberglass pipe manufacturer in order to generate the ASTM D designation code for the piping.
This cell-type format, however, is subject to misapplication since unobtainable property combinations can be selected if the user is not familiar with commercially available products. Stay on Page Continue to Compass.
The manufacturer should be consulted. Benton, Ar Cell: This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? A superscript epsilon e indicates an editorial change since the last revision wstm reapproval.
NOTE 1—For the purposes of this standard, polymer does not include natural polymers. It covers the following types, grades, and classes of machine-made? Form Box Generator Site.
Methods of classification, requirements, test methods and the method of marking are included.
It is not based on dimensions or raw material speci? The manufacturer should be consulted. Each part is one ‘designation order’ i. The inside diameter of the pipe is determined by the amount of material introduced into the mold. Astn 5—Information regarding selection of service design factors and pressure rating is provided in Practice D and the individual v2310 standards. This standard does not purport to address all of the safety concerns, if any, associated with its use.
Description of Terms Speci?
Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is not based on dimensions or raw material specifications. Table 1 presents a summary of the designation requirements. Link to Active This link will always route to the current Active version of the standard.
Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters. This standard is being withdrawn without replacement due to its limited use by industry.
Formerly under the jurisdiction of Committee D20 on Plastics, this standard was withdrawn in August Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
B Refer to Practice D to obtain classification of the values. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 2 — There is no known ISO equivalent to this standard. NOTE 3—All possible pressure strength combinations of types, grades, and classes may not be commercially available.
Pipe meeting this classi? If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. The outside diameter of the? Table 1 data was divided into 4 Parts for spacing considerations.
Changes in materials or manufacturing processes will necessitate a screening evaluation as described in Practice D Our dd2310 is too poor to buy the latest version D ; therefore, this designation code generator is based on ASTM D data which is e2310 what many manufactures use.