ASTM C114 PDF

0 Comments

C – 00 Standard Test Methods for Chemical Analysis of Hydraulic Cement, chemical analysis, compositional analysis, hydraulic cements. ASTM Standards: 2. C 25 Test Methods for Chemical Analysis of Limestone,. Quicklime, and Hydrated Lime. D Specification for Reagent Water. ASTM C accreditation for cement analysis . are within the prescribed limits for iron, so acceptable (according to ASTM-C requirement).

Author: Kazijas Nibei
Country: Iceland
Language: English (Spanish)
Genre: Environment
Published (Last): 10 February 2015
Pages: 414
PDF File Size: 8.53 Mb
ePub File Size: 16.62 Mb
ISBN: 363-2-44071-669-6
Downloads: 67015
Price: Free* [*Free Regsitration Required]
Uploader: Mikarisar

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The reference test methods are long accepted classical chemical test methods which provide a reasonably well-integrated basic scheme of analysis for hydraulic cements.

ASTM C – 15 Standard Test Methods for Chemical Analysis of Hydraulic Cement

Link to Active This link will always route to the current Active version of the standard. Active view current version of standard Translated Standard: D Where an CRM certificate value includes a subscript number, that subscript number shall be treated as a valid significant figure.

No other units of measurement are included in this standard.

Standard A by the mass fraction of Standard A in each of the other standards that is, 0. Current edition c14 April 15, Weigh and prepare two separate specimens of each standard.

Any test methods of demonstrated acceptable precision and bias may be used for analysis of hydraulic cements, including analyses for referee and certification purposes, as explained in Section 3.

When reporting the results of referee analyses, specify which test methods were used. The alternative test methods generally provide individual determination of specific components and may be used alone or as alternates and determinations within the basic scheme at the option of the analyst and as indicated in the individual method.

No other units of measurement are qstm in this standard.

General procedures include sample weighing, taring of crucibles, weighing of ignited residues, volatilization of platinum, chemical analyses, and calculation. If either of the two requirements listed above are not met, identify and correct any problems or errors found in the procedure. The alternative test methods generally provide individual determination of specific analytes and may be used alone or as alternates and determinations within the basic scheme at the option of the analyst and as indicated in the individual method.

  CANON POWERSHOT A510 MANUAL PDF

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Duplicate samples shall be tested on different days. For c1114 purpose of comparing analyses and calculating the average of acceptable results, the percentages shall be calculated to the nearest 0.

ASTM C – 09 Standard Test Methods for Chemical Analysis of Hydraulic Cement

When a lesser number of CRM cements are required, all of the values shall be within the prescribed limits. Link to Active This link will always route to the current Active version of the standard. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of asgm limitations prior to use.

The standardization used for qualification and for analysis of each constituent shall be determined by valid curve-fitting procedures.

Specific chemical test methods are provided for ease of reference for those desiring to use them. This standard is issued under the fixed designation C; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision.

CO 2 Determinations in Hydraulic Cements. The analyst is considered qualified when the difference between the duplicate results does not vary by more than the value listed in Column 2 of Table 1 and the average of the two samples agrees with the certificate value of the CRM within the limits listed in Column 3 of Table 1 after correction for minor components when needed. The final results, when corrected for blank values, should, in either case, be so designated.

A reference test method must be used where an alternative test method is not provided. Specific chemical test methods are provided for ease of reference for those desiring to use them. Longer, more complex procedures, in some instances, have been retained as alternative test methods to permit comparison of results by different procedures or for use when asym materials are being examined, where unusual interferences may be qstm, or when unusual preparation for analysis is required.

  DESCARGAR RISE OF THE OGRE EN ESPAOL PDF

Reference test methods and procedures include determination of insoluble residue, silicon dioxide, ammonium hydroxide group, ferric oxide, phosphorus pentoxide, titanium dioxide, zinc oxide, aluminum oxide, calcium oxide, magnesium oxide, sulfur, loss on ignition, sodium and potassium oxides, manganic oxide, chloride, chloroform-soluble organic substances.

Active view current version of standard. The requirements for qualification of a zstm method and analyst are summarized in Table 2. Sample preparation and general test procedures shall be followed according to the specification.

Test results from alternative test methods may be used as a basis for acceptance or rejection when it is clear that a cement does or does not meet the specification requirement.

ASTM C114 – 15 – Chemical Analysis of Hydraulic Cement

CO 2 Determinations in Hydraulic Cements. Performance Requirements for Rapid Test Methods.

Prepare three standards, each in duplicate: Referenced Documents purchase separately The documents listed below are referenced within zstm subject standard but are not provided as part of the standard. Alternative test methods and procedures include determination of calcium oxide, calcium dioxide, magnesium oxide, loss on ignition, titanium dioxide, phosphorus pentoxide, manganic oxide, and free calcium oxide.

When two or three results do agree within the permissible variation, their average shall be accepted as the correct value. Apparatus and materials for the test method include balance, weights, cc114 and laboratory containers, desiccators, filter paper, crucibles, and muffle furnace. Standard reagents for the test method shall be used within the limits of the specification.

It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. A number in parentheses indicates the year of last reapproval. The adtm test methods are long accepted classical chemical test methods which provide a reasonably well-integrated basic scheme of analysis for hydraulic cements. Originally approved in Qualification for Different Analyses.

Historical Version s – view previous versions of standard. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.