ASTM A480 PDF

0 Comments

ASTM A is the specification that covers the general requirements for flat- rolled stainless and heat-resisting steel plate, sheet and strip. It does not reference. 1 This specification is under the jurisdiction of ASTM Committee A01 on Steel, product specifications that reference Specification A/. ASTM A/AM Standard Specification for General Requirements for Flat -Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and.

Author: Nanos Zolokazahn
Country: Croatia
Language: English (Spanish)
Genre: Politics
Published (Last): 8 December 2005
Pages: 407
PDF File Size: 2.67 Mb
ePub File Size: 5.14 Mb
ISBN: 430-2-63512-563-7
Downloads: 84454
Price: Free* [*Free Regsitration Required]
Uploader: Muktilar

Notwithstanding the absence of a signature, the organization submitting the EDI transmission is responsible for the content of the report. When agreed by the seller and the purchaser, it is permitted to modify the cross section to 1? Link to Active This link will always route to the current Active version of the standard. Average surface roughness Ra may generally be up to 40 micro-inches.

This is a dull, nonre?

For plates of irregular shape, the over thickness tolerances apply to the greatest width corresponding to the width ranges shown. Historical Version s – view previous versions of standard. Hard 19 16 13 26 19 16 12? Material Test Report and Certi? It is permitted to break the corners of the cross section of the specimen with a?

Such a requirement for an element not listed in the product speci? ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. The results of this retest shall be within the speci?

Work Item s – proposed revisions of this standard. The steel shall be made by one of the following processes: When the material is too thin to allow hardness testing using any of the Rockwell super? NOTE 1—Thickness measurements are taken at least 10 mm in from the edge of the product, except that on widths less than 26 mm, the tolerances are applicable for measurements at all locations. Thickness tolerances given in mm unless otherwise indicated. The tension test specimen shall conform to the appropriate sections of Test Methods and De?

  KYRIL BONFIGLIOLI PDF

ASTM A Specification | Penn Stainless Products

Quenched in water or rapidly cooled by other means at a rate sufficient to prevent reprecipitation of carbides, as demonstrable by the capability of passing the test for resistance to intergranular corrosion speci?

B Product analysis limits for cobalt under 0.

When intergranular corrosion tests are required, they shall be as agreed upon between the seller and the purchaser. C Quenched in water or rapidly cooled by other means.

ASTM A480 Plate Thickness & Flatness Tolerances

Requirements for AM are given in Annex A3. If certifying that the material conforms to the requirements for more than one type of steel, the manufacturer may indicate each type of steel on the report, or may issue a separate report for each type of steel.

Committee A01 has identi? Within the text, the SI units are shown in brackets, except that when AM is speci? Repair of Plate by Welding C Xstm including hard axtm of 2xx and 3xx series, dead-soft sheets, and deep-drawing sheets. Such analysis shall be made by any of the commonly accepted methods that will positively identify the material. Such marking, if used, shall be part of the same marking as used for a single type of steel, or shall be a separate but similar marking immediately adjacent to the marking used for a single type of steel.

The allowable variation of a particular element in a single sample for product analysis is permitted to be either above or below the speci? Finish for Sheet NOTE 3—For plates with speci? It is permitted to obtain such specimens from specimens selected for mechanical testing.

  LOS PAPALAGIS PDF

For thicknesses under 0. B Recommended cleanup allowance which, unless otherwise speci? Average surface roughness Ra may generally x480 up to 25 micro-inches. NOTE 2—Cold-rolled sheets in cut lengths and coils are produced in some type numbers and some widths and thickness to tolerances less than those shown in the table. Bright Annealed Finish—See Note 4.

ASTM A480 Specification

However, it is permitted to specify Practice E of Practices A for Type H when intergranular corrosion is of concern. This is a general purpose? The producer is permitted to analyze for unspeci? The marking shall be sufficiently stable to withstand normal handling. Not withstanding the absence of a signature, the organization submitting the document is responsible for its content.

ASTM Specification A – What is it? – NKS

Combining values from the two systems may result in nonconformance with the specification. A number in parentheses indicates the year of last reapproval. The use of the gage number is discouraged as being an archaic term of limited usefulness not having general agreement on meaning. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

For narrow strip, the following widths can be tested: In case of dissatisfaction with the results of the test, the seller is permitted to make claim for a rehearing within that asttm. However, it is not necessary to actually run the test unless it is speci? Approved November 15, NOTE 7—The term continuously, as applied to heat asgm, is meant to describe a heat-treating operation in which one cut length follows another through the furnace.

Circular and sketch plates over 5?