AMERICAN AUDIO V1000 PDF

0 Comments

Results 1 – 34 Valuation Report for Used V Power Amplifier by American Audio (Specs: 2 ( Stereo), x 2 @ 8, Bridgeable). Output Power: W RMS Per Channel @ 4 Ohms, 1kHz, % THD W RMS Per Channel @ 8 Ohms, 1kHz, % THD – Bridge Mode, Mono W RMS. Download AMERICAN AUDIO V V SCH service manual & repair info for electronics experts.

Author: Brazragore Kagak
Country: Germany
Language: English (Spanish)
Genre: Medical
Published (Last): 20 October 2008
Pages: 94
PDF File Size: 2.22 Mb
ePub File Size: 10.90 Mb
ISBN: 169-6-28708-256-2
Downloads: 78259
Price: Free* [*Free Regsitration Required]
Uploader: Sataur

Fuse Holder – This holder houses the external fuse. This booklet contains important information concerning the proper and safe operation of your new amplifier. When the input signal decreases enough that clipping ends, the limiter will deactivate and cease its gain reduction.

If your speaker lines short, the amplifier automatically detects this problem and discontinues operation for that channel.

Below rated output, 8 ohms dB, unweighted dB, unweighted dB, unweighted dB, unweighted dB, unweighted Power Consumption: Be sure your amplifier and all other audio equipment is powered down. When the input signal overloads, the “CLIP LED’s” indicate a signal overload, at this time, the master volume should be lowered to reduce distortion. If the carton appears to be damaged, carefully inspect your unit for any damage and be sure all accessories necessary to operate the system have arrived intact.

Every Vplus series amplifier has been americah tested V and has been shipped in perfect amwrican condition. For amerian runs shorter than 20ft.

AMERICAN AUDIO V1000 POWER AMP AMPLIFIER 1000 WATTS NR!

Connect a XLR cable to the input of channel one. If the input gain level is not reduced the built-in limiter will activate. Connect your speaker across the red output binding post on the rear of your amplifier. No user serviceable parts inside. The fixture does not appear to operate normally or exhibits a marked change in performance. This amplifier is designed to mount into a standard 19″ rack. To reduce the risk of shock or damage to your amplifier, be sure that the wire connected to one binding post does not come in contact with that of another.

  JOHANSON MATTSSON 1988 PDF

Under heavy clipping activity lower the channel one gain aerican to reduce there details on input configuration. Turn your input source level up. The XLR jack is configured as follows; Pin three positive, pin two negative, pin one ground. In the event of an electrical overload the aerican will pop-out. The appliance has been exposed to rain or water. Use channel two positive output terminal for the negative connection and the channel one positive output terminal for the positive connection.

American Audio V PLUS Manuals

Audil the line from the output terminal of the amplifier to the speaker. Each channel operates independently of each other allowing each channel to have different filter settings. A limiter takes the gain of an overloading signal and reduces it, the reduction in gain reduces distortion that can cause damage to your speakers and amplifier.

The limiter has a fixed threshold and can not be adjusted. These fans are used to cool the vv1000 parts of the amplifier. Insert bare wire into the binding post and tighten. At this point channel one will begin to distort. Typical speaker output using bare wire.

AMERICAN AUDIO V POWER AMP AMPLIFIER WATTS NR! | #

P Typical speaker output using spade connectors. Turn channel two gain up. No hay piezas adentro que el usario puede reparar. An ultrasonic network uncouples RF from the output and helps keep the amplifier stable with reactive loads.

If it is lit about half the time, the amplifier channel will probably go into thermal protection within a few minutes. Please do not return the amplifier to your dealer without contacting customer support. Rear mounting the unit is especially recommended if the unit is to mounted into a mobile rack.

  ITEXTSHARP LINEARIZED PDF

The Output Short Circuit V Protection protects the output devices of the amplifier from short circuits and stressful loads.

Turn your amp on. The power-supply cord or the plug has been damaged. Never block the fan grills in any way or mount in an aidio rack, doing so may cause the amplifier to overheat and fail.

Use your front gain controls to regulate the output volume. See page 9 for more details on input configuration. If this line good, check the internal speaker connections and components.

Antes de usar este amplificador, lea mas advertencias en la guia de operacion. Please read and understand this manual completely before attempting to operate your new amplifier. You may also visit us on the web at www. The unit also amercan a way to rear mount the unit into a rack for added security.

Risiko – Elektrischer Schlag!

You’re reading an excerpt. Always use the 50 Hz filter setting if you are using the amplifier to drive a distributed line system also known as a constant-voltage line, 70 volt line, etc. Use the channel one gain to regulate your amplifier output.

Operating instructions AMERICAN AUDIO V1000 PLUS

When connecting your speakers to the amplifier using banana jacks; Be sure that the red and black caps on the binding post are tighten down completely. Diagram 10 When connecting your speakers to the amplifier using bare wudio Unscrew the red and black caps on the binding post, be sure not to completely remove or unscrew the red and black caps.

To reset the breaker, push it in. All channel output during the “Short Circuit Protection” will be interrupted i.